Ta-triumph-adler DC 2315 User Manual

Instruction HandbookDC 2315Digital MultifunctionalSystem

1-2INSTALLATION PRECAUTIONSEnvironment CAUTIONAvoid placing the copier on or in locations which are unstable or not level. Such locations may cause th

1-3PRECAUTIONS FOR USECautions when using the copierWARNINGDO NOT place metallic objects or containers with water (flower vases, flower pots, cups, et

1-4Other precautionsDO NOT place heavy objects on the copier or cause other damage to the copier.DO NOT open the upper front cover, turn off the power

1-5Laser SafetyLaser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside this machine is hermetically seal

1-6CAUTION!The power plug is the main isolation device! Other switches on the equipment are only functional switches and are not suitable for isolatin

1-7DECLARATION OF CONFORMITYTO89/336/EEC, 73/23/EEC and 93/68/EECWe declare under our sole responsibility that the product to whichthis declaration re

1-8

2-1Section 2 NAMES OF PARTS(1) Original cover(Open/close this cover when you are setting the original on the platen.)(2) Platen(Set originals here for

Section 2 NAMES OF PARTS2-2(12) Drawer(This drawer has a storage capacity of 250 sheets of standard copy paper (80 g/m²).)(13) Paper width guides(Adj

Section 2 NAMES OF PARTS2-3(20) Power switch(Turn this switch ON ( | ) before copying.)(21) Face-up tray(Finished copies can be ejected and stored fa

All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photoc

Section 2 NAMES OF PARTS2-4(1) Start key & indicator(Press this key when you want to start copying. Copying will begin immediately if you press t

Section 2 NAMES OF PARTS2-5(14) Sort key & indicator(Press this key when you want to copy with the Sort mode. Make sure that the Sort indicator i

Section 2 NAMES OF PARTS2-6

3-1Section 3 PREPARATIONSCopy paper can either be loaded into the drawer(s) or set on the multi-bypass tray.Note when adding paperAfter taking new pap

Section 3 PREPARATIONS3-21 Pull the drawer all the way out of the copier.IMPORTANT!When pulling the drawer out of the copier, be sure to support it s

Section 3 PREPARATIONS3-35 Push the drawer securely all the way back into the copier until it stops.IMPORTANT!If you will not be using the copier for

Section 3 PREPARATIONS3-44 Press down on the stopper extension lock and slide the paper stopper towards the rear of the drawer to set the lock into p

Section 3 PREPARATIONS3-54 Press the Number of Copies / Zoom(+) or Number of Copies / Zoom(-) key to select the appropriate paper size. The displayed

Section 3 PREPARATIONS3-61 Open the multi-bypass tray towards you until you hear it click into place.2 Pull out the multi-bypass extension and then f

Section 3 PREPARATIONS3-7Selecting the paper sizePerform the following procedure to use the operation panel and select the size of paper that is set

iThe explanations contained in this operation guide have been separated into different sections in order to allow even those using a copier for the fi

Section 3 PREPARATIONS3-8Selecting the paper size (temporary setting)1 Press the Paper Select key until the multi-bypass tray indicator is lit.2 Pres

Section 3 PREPARATIONS3-9Thick Paper modePerform the following procedure to select the Thick Paper mode when copying onto thick copy paper (90 g/m² –

Section 3 PREPARATIONS3-10When copying onto special paper, such as thick paper (90 g/m² – 163 g/m²) and OHP transparencies, ALWAYS use the face-up tr

4-1Section 4 BASIC OPERATION1 Warm-upTurn the power switch ON ( | ). At the end of warm-up, the Start indicator will light.2 Selecting the desired fun

Section 4 BASIC OPERATION4-25 Adjusting the copy exposureThe copy exposure can be manually adjusted in all of the image quality modes, except for the

Section 4 BASIC OPERATION4-39 At the end of copyingFinished copies will be ejected onto the copy storage table.NOTEThe copy storage table has a stora

Section 4 BASIC OPERATION4-4Zoom modeWith this mode, the magnification ratio can be set to any 1% increment between 50% and 200%.1 Press the Recall%/

Section 4 BASIC OPERATION4-5Preset Zoom modeWith this mode, the magnification ratio can be set to one of the pre-set ratios:1 Press the Reduce/Enlarg

Section 4 BASIC OPERATION4-6The Low Power mode automatically puts the copier into a state of sleep if no operation has been performed on the copier f

Section 4 BASIC OPERATION4-7The Off mode automatically turns most of the power to the copier off if no operation has been performed on the copier for

iiCONTENTSEnergy Star Program ...ivPlease read this Operation Guide before using t

Section 4 BASIC OPERATION4-8

5-1Section 5 COPY FUNCTIONSWith this mode, the images from either 2 or 4 originals can be reduced and then combined onto a single copy. In addition, t

Section 5 COPY FUNCTIONS5-2Caution on setting the originalsThe following illustrations indicate how the orientation of the original will affect the r

Section 5 COPY FUNCTIONS5-3<When setting the originals in the Document Processor>NOTEMake sure the originals are set so that the first page is

Section 5 COPY FUNCTIONS5-41 Press the 2in1/4in1 key until the 2in1 indicator lights.NOTEIt is possible for you to change the type of borderline. (Se

Section 5 COPY FUNCTIONS5-54-in-1Use this mode when you want to copy four originals onto each sheet of copy paper.Caution on setting the originalsBe

Section 5 COPY FUNCTIONS5-63 Press the Start key. Scanning of the first original will start.NOTEIf the optional Document Processor is installed on yo

Section 5 COPY FUNCTIONS5-74 Press the Number of Copies / Zoom(+) or the Number of Copies / Zoom(-) key to select the desired borderline.The displaye

Section 5 COPY FUNCTIONS5-84 Press the Number of Copies / Zoom(+) or the Number of Copies / Zoom(-) key until the number that corresponds to desired

Section 5 COPY FUNCTIONS5-9Multiple originals can be scanned into memory in a single operation and then the desired number of copy sets created.1 Pre

iiiMAKING FULL USE OF THE COPIER’S ADVANCED FUNCTIONS1 Enlarging/reducing copies to a desired size between 50% and 200% <Zoom mode> (See page 4-

Section 5 COPY FUNCTIONS5-10By registering often used settings in advance as a single program, it is possible for you to make copies using those same

6-1Section 6 COPY DEFAULT SETTINGSThe state that the copier enters at the end of warm-up or when the Reset/Power key is pressed is called the “initial

Section 6 COPY DEFAULT SETTINGS6-2F07 Text Mode Exposure AdjustmentAdjusts the exposure for when the Text mode is selected as the image quality mode.

Section 6 COPY DEFAULT SETTINGS6-3F14 Multi-Bypass Tray Paper SizeRegisters the size of paper that is to be set on the multi-bypass tray.* The “XXX”

Section 6 COPY DEFAULT SETTINGS6-4F21 Off Mode ON/OFF Sets whether the Off mode (see page 4-7), which automatically turns most of the power to the co

Section 6 COPY DEFAULT SETTINGS6-5F27 Upper Drawer Skewed Feed AdjustmentAdjusts for off-center printing. -1.0 – 3.0 (mm)(Adjustment is complete at t

Section 6 COPY DEFAULT SETTINGS6-6NOTEIf you want to access the “F30” default item (Document Processor Skewed Feed Adjustment), proceed directly to s

Section 6 COPY DEFAULT SETTINGS6-7Sample User Copy Setting ListSample Toner Coverage Report5 Press the Number of Copies / Zoom(+) or the Number of Co

Section 6 COPY DEFAULT SETTINGS6-88 Press the Recall%/Enter key. The operation panel will return to the display in step 2. Once you are finished acce

Section 6 COPY DEFAULT SETTINGS6-914 Press the Recall%/Enter key. If you are finished making adjustments, press the Stop/Clear key. The operation pan

ivEnergy Star Pr ogramWe have determined as a participating company in the International Energy Star Program that this product is compliant with the

Section 6 COPY DEFAULT SETTINGS6-1020 Prior to performing the adjustment procedure, it is necessary to use the Document Processor to make copies in a

Section 6 COPY DEFAULT SETTINGS6-1128 Prior to performing the adjustment procedure, it is necessary to use the Document Processor to make copies in a

Section 6 COPY DEFAULT SETTINGS6-12It is possible to use the operation panel to check the total number of copies made. It is also possible to print o

7-1Section 7 OPTIONAL EQUIPMENTDocument ProcessorAutomatically feeds and scans multiple sheet-originals one by one.Acceptable originals• Use sheet ori

Section 7 OPTIONAL EQUIPMENT7-2Setting originals in the Document Processor1 Adjust the original insert guides to fit the width of original(s) to be c

Section 7 OPTIONAL EQUIPMENT7-3Setting originals on the platenWhen copying from an original which cannot be set in the Document Processor (books, mag

Section 7 OPTIONAL EQUIPMENT7-4Paper FeederAn extra drawer can be added below the drawer that is included with this copier.The type, sizes and amount

8-1Section 8 TROUBLESHOOTINGWhen any of the following indications appears on the copy quantity/magnification display, perform the corresponding proced

Section 8 TROUBLESHOOTING8-2“E72” appears on the copy quantity/magnification displayOriginals for another job were set in the optional Document Proce

Section 8 TROUBLESHOOTING8-3If a paper jam occurs, copying will stop. In this case, an indication about the jam will appear on the operation panel.Le

vPlease read this Operation Guide before using the copier. Keep it close to the copier for easy reference.Please read this Operation Guide before usin

Section 8 TROUBLESHOOTING8-4Removal proceduresPaper jam inside the copierNOTEIf there are any finished copies on the copy storage table, remove them

Section 8 TROUBLESHOOTING8-5Paper jam in a drawer1 Pull out the drawer that is currently being used.2 Remove the jammed paper.NOTEIf a paper jam occu

Section 8 TROUBLESHOOTING8-6Paper jam in the paper eject section1 Open the face-up tray.2 Remove the jammed paper.3 Close the face-up tray.4 Open and

Section 8 TROUBLESHOOTING8-7Paper jam in the multi-bypass tray1 Remove all of the paper remaining on the multi-bypass tray.2 Open and then close the

Section 8 TROUBLESHOOTING8-85 Remove the jammed original.6 Close the Document Processor.7 Reset the originals.

Section 8 TROUBLESHOOTING8-9If trouble occurs with your copier, carry out the applicable checkpoints and procedures indicated on the following pages.

Section 8 TROUBLESHOOTING8-10Black or white vertical bands appear on the copies.Is the charger cleaner in its home position (marked “CLEANER HOME POS

9-1Section 9 MAINTENANCE AND OPERATION INFORMATIONLift open the original cover and wipe the gray portion, as shown in the illustration, with a soft cl

Section 9 MAINTENANCE AND OPERATION INFORMATION9-2When toner runs low, the Add Toner indicator will light. If you continue to make copies while the A

Section 9 MAINTENANCE AND OPERATION INFORMATION9-34 Pull the lock lever towards you into its release position (marked “UNLOCK”), then pull the toner

vi

Section 9 MAINTENANCE AND OPERATION INFORMATION9-49 Hold the Process Unit stable and push on the areas marked “PUSH HERE” on the toner container, unt

Section 9 MAINTENANCE AND OPERATION INFORMATION9-514 Close the front cover.15 Close the upper front cover.After use, ALWAYS dispose of the toner cont

Section 9 MAINTENANCE AND OPERATION INFORMATION9-6Main BodyType...Deskt

Section 9 MAINTENANCE AND OPERATION INFORMATION9-7Document Processor (option)Original feed system...

Section 9 MAINTENANCE AND OPERATION INFORMATION9-8• Recovery time from the Low Power mode...10 seconds• Transition time to the Low Pow

Section 9 MAINTENANCE AND OPERATION INFORMATION9-9The following explains the locations for attaching option equipment.Available optionsThe following

9-10Appendix: Functions and settings combination chart{: Combination is possible---: Combination is NOT possibleU1: The settings for the registered pr

IndexNumerics2-in-1 ...5-14-in-1 ...

SSelecting the desired functions ...4-1Selecting the image quality ...

MEMO

1-1Section 1 IMPORTANT! PLEASE READ FIRST.CAUTION LABELSCaution labels have been attached to the copier at the following locations for safety purposes

E1

UTAX GmbH, Ohechaussee 235, 22848 Norderstedt, Germany